This is a Grade A used LED panel with barn doors listed on OxGears, and the honest answer is that the listing tells you the condition grade and almost nothing else: light source, power, beam angle, colour, control, network, dimensions, weight and voltage all read On request. Buy it only after you have confirmed the light engine, the control protocol and the physical state of the barn doors and yoke directly with the seller, because the page itself will not answer those questions. Start from the product page and treat every blank field as an open question rather than a default.
1. The only confirmed fact is the A condition grade; every technical field on the listing is On request, so the spec sheet cannot drive your decision. 2. Barn doors are a mechanical accessory — check hinge tension, blade flatness and whether the frame seats correctly before anything else. 3. Control protocol and network capability are undisclosed, so you must confirm DMX or other input compatibility against your existing console before committing. 4. Quantity is on request, which means lot size, matching units and spare availability are all still open.
The listing sits in the LED fixtures category and carries a single hard data point: condition grade A. Everything else in the specification block is recorded as On request — light source, power, beam angle, colour, control, network, dimensions, weight and voltage. Quantity available is on request.
That combination is more informative than it looks. A grade A classification on a used fixture normally means the unit has been assessed as functional and cosmetically sound for resale, but the grade is a condition statement, not a performance statement. It says nothing about output level, colour consistency across the panel, or whether the barn doors are original to the unit. Because the technical fields are blank rather than filled with approximate values, the seller is not asserting any photometric or electrical figure you could hold them to. That is the correct way to read it: absence of data is not a claim of adequacy.
The second implication is about deployment. A panel fixture with barn doors is a controlled-spill light — the doors exist to cut the edges of the beam and keep light off surfaces you do not want lit. That tells you the intended use is stage wash, side light or architectural accent at moderate distance, not long-throw front-of-house work. Without a beam angle figure you cannot calculate coverage, so the practical constraint is that you must plan throw distance and coverage on site rather than from a drawing.
Third, the missing voltage field matters for export. Buyers in the Middle East, Southeast Asia, Africa, Europe and South America run different mains standards, and a fixture that cannot be re-strapped or is fixed to one voltage becomes a single-market asset. Confirm the input voltage and whether it is switchable before you price the unit into a rental fleet.
The gap list here is long and each item changes the decision.
Serial history and prior use are not disclosed. A panel that spent its life in a fixed install at low duty is a different asset from one that toured in a rental fleet. You cannot tell which from the page.
Service records and actual hours are not disclosed. LED panels degrade in output and shift in colour over time, and without an hours figure or a service history you have no basis for estimating remaining useful output. This is the single biggest unknown for any used LED fixture.
Control protocol is not disclosed. Whether the unit takes DMX, a proprietary protocol, or has network input determines whether it drops into your existing rig or needs a converter and a new control layer. For a rental company this is a direct cost item.
Flight-case condition is not disclosed. If the unit ships in a case, the case is part of the value; if it does not, you are paying to build transport packaging for a fragile panel with protruding barn doors.
Quantity available is on request. If you need eight matching units for a venue install, a single unit is not a solution and a mixed batch may not colour-match. Buyers who need a second barn-door panel to compare condition and packing against this one can check the Baier Vires BS-K5 listing before agreeing a price.
Colour and beam angle are not disclosed. Colour temperature and consistency across a batch cannot be assumed, and beam angle governs whether the fixture is usable at your trim height.
Do not choose this unit if your project requires documented photometrics. A broadcast studio, a theatre with a lighting plot that has to be submitted for approval, or an integrator writing a specification for a client cannot build on a fixture whose light source, beam angle and colour are all unstated. The paperwork will not close.
Do not choose it for long-throw front-of-house work. A barn-door panel is a short-to-medium throw tool; without a beam angle figure you cannot demonstrate coverage at distance, and the doors will not help you reach it.
Do not choose it if you need a matched multi-unit array and cannot confirm quantity and batch consistency. Colour shift between panels is visible on camera and on stage, and the listing gives you no basis to promise matching.
Do not choose it if your control infrastructure is fixed and non-negotiable. With control and network both On request, a unit that turns out to need a protocol converter is a hidden cost you did not price.
Finally, do not choose it if you are buying remotely with no inspection path. On a fixture this under-specified, buying blind is a bet on the seller, not on the product. For nightclub and bar installs where spill control matters, pair the fixture with a matching nightclub bar sound system plan so lighting and audio are specified together.
Grade A versus missing data. The grade is reassuring on condition but the blank spec block means you are trading documentation for availability. If this exact fixture type is scarce in your market, that trade can be worth it; if equivalents are common, insist on a unit with a filled spec sheet.
Barn doors as value versus barn doors as risk. The doors are the reason to buy this configuration, but they are also the most likely damaged part — bent blades, loose hinges and missing frame screws are common on used units and are not covered by a condition grade that focuses on the fixture body. Budget for replacement hardware or negotiate it into the deal.
Single unit versus fleet. Quantity is on request, so the trade-off is between taking one unit now and waiting to confirm whether a matching lot exists. For rental companies, one odd fixture is a spare, not inventory.
Export logistics versus fixture fragility. A panel with barn doors is awkward to pack. If no flight case is included, the shipping cost and damage risk rise, and that changes the landed cost comparison against a new unit. Review how the category is generally handled on the LED fixtures page before you commit to a shipping plan.
Voltage flexibility versus market reach. An undisclosed voltage means you may be buying for one market only. If you resell across regions, that narrows the resale audience.
Ask for availability and a quote through the contact page and put these questions in the same message so the seller answers them together: the light source type and approximate output, the input voltage and whether it is switchable, the control protocol and connector type, the beam angle, the dimensions and weight, the quantity available and whether the units are a matching batch, and whether a flight case is included.
Then ask for photographs of the barn doors open and closed, the rear panel and connectors, the yoke and mounting hardware, and any label plate showing voltage and model information. Ask whether the unit has been powered on and whether all LED segments illuminate evenly.
If the value justifies it, request a short video of the fixture running at full and at low output so you can see colour consistency and any dead segments. Confirm the incoterm you are quoting against, and confirm packing method before you agree a price, because a panel without a case changes the landed cost materially.
Do not pay a deposit until the control protocol and voltage are confirmed in writing. Those two facts determine whether the unit is usable in your market at all.
The listing records condition grade A. No further condition detail, service history or hours are disclosed.
Light source, power, beam angle, colour, control, network, dimensions, weight and voltage are all listed as On request. They must be confirmed with the seller.
Quantity available is on request. The listing does not state a number.
Not disclosed in the listing. Confirm packing and case inclusion with the seller before agreeing a price.
No price, warranty period, lead time or MOQ is stated in the materials. Request a quote for the unit. ## Sources
OxGears listing: used LED panel with barn doors (led-fixtures), oxgears.com — listing data as provided, including condition grade A and On request technical fields.
Manufacturer published specifications for LED panel with barn doors — not available in the materials supplied; no URL provided. Buyers weighing a single panel against a broader fleet should browse the used stage lighting range to see how barn-door fixtures are typically presented and packed for export.
Need condition photos or test results before you commit? Contact our team and we reply within one working day.
Professional LED soft panel light for film/TV and stage use, equipped with adjustable barn doors to control beam spread. Sturdy metal housing, supports desktop or stand mounting, suitable for studio, live performance, and video production fill lighting.
A practical condition and inspection guide for the used WGS Lighting ML-009 RGBAW LED fixture, covering DMX/RDM checks, optics, power and export packing.
Practical guide to buying used LED PAR 18x10W RGBAW fixtures: what to inspect, how Grade A is assessed, DMX checks and export packing tips.
Practical guide to the used JINBEI MINI LEDSPOT: 30W RGBW LED, 15° beam, DMX512 control, Grade A condition, and what B2B buyers should check before export.
